Atec Astro-Med-Dash-10 User Manual download pdf

Dash 10 Specifications

Input Type Single-ended isolated

User Input Connector Guarded Binding Posts

Input Range 50 mVfs to 500 Vfs

Operating Modes Peak-to-peak or RMS

Input Coupling DC

Input Impedance 1 Megohm

Input Isolation

1500 VACrms for 60 sec., channel to channel,

channel to chassis

Maximum Input 250 Vrms, 500 VDC, 500 Vpeak

CMR (IMR) Greater than 95 dB @ 60 Hz

Common Mode

Voltage

250 Vrms

Frequency Response -1dB at 12 kHz, -2 dB at 18 kHz, -3 dB at 22 kHz

A/D Sample Rate 200 kHz filter disabled

Filter Type 2 pole 12 dB/octave

Filter Response -3dB at 8.75 Hz

Chart Speed Accuracy ± 2%

Zero Suppression

Range

± 500 V or ± 5V on mV ranges

Zero Suppression

Accuracy

± 2% of zero suppression setting

Zero Position

Accuracy

± 0.2%

Battery Charge Time 19 Hours with power off

Battery Life 30 minutes nominal

Operating

Temperature

0 degrees C to 45 degrees C

Storage Temperature -20 degrees C to 80 degrees C

Operational Relative

Humidity

0% to 95% RH non-condensing

Operational Vibration 2G

Weight 32 lbs. without battery, 36 lbs with battery

Timer Speeds

0.01 to 0.09 (0.01 second increments) 0.1 to 0.9

(0.1 sec. increments); 1.0 to 9.0 (1.0 sec.

ncrements); 10.0 to 60.0 (5.0 second increments)

Internal Event

Markers

10 interchannel plus 1 system

Internal Annotation

Buffers

Thirty 128-character buffers, One 28-character

system log buffer, One 128-character on-demand

uffer

Host Interfaces RS-232, Xon/Xoff or Hardwire; GPIB standard

Baud Rate 300, 600, 1200, 2400, 4800, 9600, 19200

GPIB Address 1 to 31

Data Capture Memory 6 Megasamples (optional - 10 channels)

Stacked Captures 2-8 captures

Data Capture Archive

to/from Floppy Time

22 KBytes per second

Sample Rates

250 kHz, 125 kHz, 50 kHz, 25 kHz, 10 kHz, 5 kHz,

2,5 kHz, 1 kHz, 500 Hz, 250 Hz, 100 Hz, 50 Hz, 25

z, 10 Hz, 5 Hz

Playback

Magnification

x1 - x25 (increments of 1); x1/2 - x1/25 (in steps

of 1/x where x is an integer between 2 and 25)

Cold Start Drift 2.0% in 30 minutes

Intrinsic Noise less than 0.5 mm

Baseline Offset less than 0.2 mm

Calibration Accuracy ± 0.8%

RMS Accuracy

± 5% for ranges less than 10VFS

± 2% for ranges greater than 10VFS

RMS Crest Factor 7% at crest factor of 10

Non-linearity < 0.1%

Dash 10 Specifications 1

Summary of Contents

Page 1 - Dash 10 Specifications

Dash 10 Specifications Input Type Single-ended isolatedUser Input Connector Guarded Binding PostsInput Range 50 mVfs to 500 VfsOperating Modes Peak-to

Comments to this Manuals

No comments

Atec Astro-Med-Dash-10 User Manual

Browse online or download User Manual for Equipment Atec Astro-Med-Dash-10. Atec Astro-Med-Dash-10 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Atec Astro-Med-Dash-10