Atec Agilent-N4010A User Manual download pdf

Agilent

N4010A Wireless Connectivity Test Set

and N4011A MIMO/Multi-port Adapter

Data Sheet

N4010A Introduction

The Agilent N4010A wireless connectivity test set is a

measurement solution that enables efficient and lower

cost test for products and components that incorporate

Bluetooth

wireless technology, Wireless LAN (WLAN),

and other emerging wireless connectivity technologies.

The Bluetooth (N4010A Option 101) feature set provides

the ability to connect to Bluetooth version 1.1 and 1.2

devices in either test mode or normal mode, and make

measurements in accordance with the Bluetooth RF test

specification. Bluetooth EDR link plus measurements

(Option 107) add BTv2.0+EDR support and enhanced data

rate (EDR) measurement capabilities.

Bluetooth audio generation and analysis (Option 113),

simplifies Bluetooth audio test configurations and provides

cost-effective functional test of Bluetooth audio devices

by performing a basic set of audio measurements. Headset

profile (Option 112) enables testing of Bluetooth voice

channels, audio gateway, and headset products.

The N4017A Bluetooth

graphical measurement application,

a PC-based software product, works in a complementary

manner with the N4010A test set and provides the ability

to fully configure the test set and display

both numerical and graphical results.

The Wireless LAN feature set (N4010A Option 102/102)

combines a fully-calibrated vector signal generator and

wide bandwidth signal analyzer into a single test set,

which enables efficient and repeatable WLAN module

test from R&D through to production. N4010A Option 108

provides the software license for the 802.11n MIMO

modulation analysis measurements within the test set.

The N4010A test set also works with the Agilent 89601A

and 89607A vector signal analyzer software. This software

provides the flexibility to make a broad range of measure-

ments for evaluating wireless formats in the 2.4 GHz or

5 GHz band, including ZigBee/IEEE 802.15.4.

The test set will meet its warranted performance after

one hour within the stated environmental operating range

plus 40 minutes after turn on. Unless otherwise stated, all

specifications are valid over the temperature range 20 to

30 °C. Supplemental characteristics are intended to provide

additional information, useful in applying the instrument by

giving typical (expected), but not warranted, performance

parameters. These characteristics are shown in italics or

labeled as nominal.

1 2 3 4 5 6 ... 15 16

Summary of Contents

Page 1 - Agilent

Agilent N4010A Wireless Connectivity Test Set and N4011A MIMO/Multi-port Adapter Data SheetN4010A IntroductionThe Agilent N4010A wireless connectivity

Page 2 - Bluetooth Specifications

10200300500 7001000200030004000201612840PercentFrequency (Hz)0 dBm0–30 dBm0–45 dBm0–15 dBm0Figure 2a. CVSD distortion percentage characteristic10–10–3

Page 3 - Carrier frequency drift

11Wireless LAN specificationsN4010A Options 102/103 WLAN Tx/Rx analysisMeasurementsThe table below shows the key measurements covered by the N4010A Op

Page 4 - Maximum input level

12N4010A vector signal analyzer specificationsWhen used with 89601A/89607A (requires Option 110 and at least one of Option 101, 102, or 103). For the

Page 5

13PC Hardware specifications• Microsoft® Windows® 2000 and XP® only• 2.4 GHz Pentium® or equivalent minimum, 2.8 GHz recommended• 200 MH availabl

Page 6 - Bluetooth EDR receiver tests

14N4011A IntroductionThe N4011A MIMO/Multi-port Adapter is a ¼ rack-width unit, used in conjunction with a N4010A test set to provide additional featu

Page 7 - ±210 Hz, ±200 Hz typical

15Ordering InformationModel number DescriptionN4010A Wireless Connectivity Test SetN4010A-101Bluetooth testN4010A-107Bluetooth EDR link plus measureme

Page 8

Agilent Email Updateswww.agilent.com/find/emailupdatesGet the latest information on the products and applications you select. Agilent Channel Partner

Page 9

2Bluetooth SpecificationsN4010A Option 101 Bluetooth• Provides ability to act as a Bluetooth master, perform inquiry, and establish a connection i

Page 10 - Frequency (Hz)

3Initial carrier frequency toleranceLink conditionsLink mode Test mode (loopback, Tx), normal mode (ACL)Hopping1On or offPacket type1DH1, DH3, DH5, HV

Page 11 - Wireless LAN specifications

4Sensitivity – multi-slot packetsLink conditionsLink mode Test mode (loopback)Hopping On or offPacket type DH1, DH3, DH5Payload PRBS9, BSOO, BSFF, BSO

Page 12 - Frequency specifications

5N4010A Option 107 Bluetooth EDR link plus measurementsBluetooth EDR transmitter testsEDR relative transmit powerLink conditionsLink mode Test mode (l

Page 13 - Regulatory information

6Bluetooth EDR receiver testsEDR Rx sensitivityLink conditionsLink mode Test mode (loopback)Payload PRBS9, BSOO, BSFF, BS55Packet type 2-DH1, 2-DH3, 2

Page 14 - N4011A Introduction

7N4010A Option 101 and Option 107 signal sourceThe N4010A signal source is used in Bluetooth test cases described earlier in this document.FrequencyRa

Page 15 - For More Information

8N4010A Option 113 Bluetooth audio generation and analysis1 N4010A Option 113 simplifies Bluetooth audio test configurations and provides cost-effecti

Page 16 - Revised: October 14, 2010

9200300500 70010002000300040000 dBm0–15 dBm0–30 dBm0–45 dBm0Frequency (Hz)dBm10–10–30–50–70–90Figure 1. CVSD frequency response

Comments to this Manuals

No comments

Atec Agilent-N4010A User Manual

Browse online or download User Manual for Equipment Atec Agilent-N4010A. Atec Agilent-N4010A User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Equipment Atec Agilent-N4010A